rvupgradestore.com Composet Products Fridge Defend
RV Life Magazine RV Park Reviews RV Trip Wizard

Author Topic: Hard wiring LED awning lights  (Read 593 times)

head1855

  • Posts: 2
Hard wiring LED awning lights
« on: February 22, 2018, 09:22:51 AM »
I would like to install some LED under awning lights. My question is can they be hardwired into the power supply for the awning motor? I am really nervous about drilling into the side of the camper. Also, does anyone have any advice on the lights I should purchase? I would like some without any backing tape on them so that I could use the more sturdy 3M VHB tape. My experience is that the backing tape that comes on these products does not usually last.

John From Detroit

  • ---
  • Posts: 21271
  • ^My New Home^
    • Diabetics Forum
Re: Hard wiring LED awning lights
« Reply #1 on: February 22, 2018, 06:06:00 PM »
Knowing, as I do how that is wired I woudl suggest against it.  But yes you can before the controller

Why not use the porch light circuit?????
Nothing adds excitement like something that is none of your business
My Home is where I park it.

glen54737

  • ---
  • Posts: 1284
  • My camping buddy
Re: Hard wiring LED awning lights
« Reply #2 on: February 22, 2018, 08:12:28 PM »
I used these ones they are waterproof and have the 3m tape already applied
https://www.ebay.com/itm/RV-Awning-Color-Changeable-LED-Lights-w-Remote-Motor-Home-Camper/301195703553?hash=item4620a9b501:m:mdEW8vuJ31_M1qH2MQBxVMg

I drilled a hole but you could always use the porch light too. The awning motor may not have power unless it's moving.
2018 Thor Miramar 35.2
2015 F-350 CC short box 6.7l 3.55 axle
2015 Alpine 3510RE-sold

Glen,Nene
Mickey & Jayco (yorkies)

grashley

  • ---
  • Posts: 4944
  • Western KY for now.
Re: Hard wiring LED awning lights
« Reply #3 on: February 22, 2018, 10:58:06 PM »
As has been said, the motor only gets power when it is running, so that will not work unless you wire into the circuit BEFORE the motor switch / controller.  I like the patio light suggestion!
Preacher Gordon, DW Debbie
09 Grand Junction 35 TMS  Progressive HW50C
Andersen Ultimate hitch
2013 F350 Lariat LB SRW Supercab diesel 4X4   TST TMS  Garmin 760
Nimrod Series 70 popup (sold)
It's not a dumb question if you do not know the answer.

jvangurp

  • ---
  • Posts: 6
    • Lucille's Adventures - Our 2004 Roadtrek 190P
Re: Hard wiring LED awning lights
« Reply #4 on: February 26, 2018, 07:19:25 AM »
I'm planning to wire up a strip of LEDs under my awning but I'm going to connect into the existing outside porch light. It seems like the easiest way to do it as it's already switched.
2004 Roadtrek 190 Popular

Summitbeerowl

  • ---
  • Posts: 15
Re: Hard wiring LED awning lights
« Reply #5 on: March 12, 2018, 03:18:06 PM »
So does anyone have some pics they can share?
I purchased a strip of LEDs that has a connection on each end. So Iím thinking I can cut it at about 4í and mount that going toward the rear of the TT from the outside door light and mount the remaining strip going toward the front.
Would it be better to drill into the side of the trailer above the light and hopefully follow the wires from the door light to the switch and then install another switch?
Or drill a hole into the door light housing and just use that?
I like the individual switch idea for each light.
Has anyone used the aluminum channels on amazon to run their LEDs in?
I think that would look more professional but not sure how they connect together. Love to see some pics of them installed.
Any help and suggestions are much appreciated!
Thanks