rvupgradestore.com Composet Products Fridge Defend
RV Life Magazine RV Park Reviews RV Trip Wizard

Author Topic: Rm1350 refer not cooling  (Read 1529 times)

Coopster8

  • ---
  • Posts: 41
Rm1350 refer not cooling
« on: April 25, 2018, 06:27:25 PM »
Hey all,
We are a proud owner of a 2009 keystone challenger, but we're finding out some little (big) problem. Our rm1350 isnt cooling.. the freezer is cold, but the refer is nicely maintaining 50 degrees, i checked the fans, they work, but never heard them come on. I drove it to the camp another camp site an hr away and guess what, it went down to 33😁 well in a couple hrs it was back to 50😭 .
Any advice/suggestion would be great

donn

  • ---
  • Posts: 3165
Re: Rm1350 refer not cooling
« Reply #1 on: April 25, 2018, 07:28:00 PM »
Clean the chimney.

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #2 on: April 25, 2018, 08:14:13 PM »
Clean the chimney?? How is this done?? Im sure i might find in youtube.

donn

  • ---
  • Posts: 3165
Re: Rm1350 refer not cooling
« Reply #3 on: April 25, 2018, 08:23:49 PM »
Climb up on the roof, take the top cover off.  Using a wire brush scrub the chimney.  Its just like a chimney sweep does for your home.  Follow by blowing all the debris out.  Carefully clean up the crud.  Before you start tape the burner orifice to protect it from being clogged.

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #4 on: April 25, 2018, 08:42:52 PM »
Ok thank you, but everything i find on YouTube is if its not working on gas. I have put the thermostat outside to trick it, and it still don't lower in temperature below 50 or so, on gas or electric. I have put a fan on the back fins for a day and still don't drop. The freezer gets cold but the refer dont. I will clean chimney tomorrow, to see if that works. My chimney is dont go though the roof, since my refer is in my slide.
I have jumped the fans as well and ran for a day. The only time it stayed cool was going to new site. (33 degrees) i ran gas only, thinking its control board, still holds at 50 😠, 

8Muddypaws

  • ---
  • Posts: 2546
Re: Rm1350 refer not cooling
« Reply #5 on: April 25, 2018, 10:33:02 PM »
That it cooled better while traveling is a pretty good indication of poor airflow. 

If the refer is installed in a slide there will be some luan panels to route the hot airflow out the side vents.  If that panel has come loose hot air could be pooling.

If it's not installed in a slide there may still be luan panels.

There will be a thermostatic switch attached to one of the fins on the cooling unit.  If it's not making good contact with the fin that could be part of the problem.  Are you sure the fan(s) are coming on?

Cleaning the chimney is good advice.  Anything, and we do mean anything that blocks the convection airflow is a problem.

Several people on here have added 12v computer fans to draw air through the system.  I'm one of them.  My 1201 LRIM is consistently 34-37F in the refer box and -18F in the freezers.  I used 4 fans and a 180F thermostatic switch to turn the fans on when needed.  My refer is in a slide.

Good luck with it.
Retired computer professional
Musician, songwriter and music director
2006 Bounder 34H, 2008 CR-V Toad

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #6 on: April 26, 2018, 11:04:47 AM »
I will install more fans and clean chimney today, also look for the luan panel as well, anything has to be better than what im doing now.. I will keep you updated on the status of the recommendations also the wind theory makes sense..
Hoping for the best

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #7 on: April 26, 2018, 05:10:25 PM »
Ok.. 2 more powerful fans installed, i pointed them up towards the fins.. my refer is in the slide, but dont see any luan panel or anything that routes the heat out of my refer compartment. I by passed the thermostat on fins to see if that helps..
I work on chimney this weekend, but will keep you updated

8Muddypaws

  • ---
  • Posts: 2546
Re: Rm1350 refer not cooling
« Reply #8 on: April 26, 2018, 06:56:02 PM »
From my experience trying to force air through the system is about half as effective as drawing it through with exhaust fans.  If you search on 'Muddypaws Mod' you find my old posts covering everything I did to my refer.
Retired computer professional
Musician, songwriter and music director
2006 Bounder 34H, 2008 CR-V Toad

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #9 on: April 26, 2018, 08:02:38 PM »
Another stupid question concerning my problem. The black tank on the cooling system, should it be warm to the touch, or hot to touch? Mine is hot to touch

donn

  • ---
  • Posts: 3165
Re: Rm1350 refer not cooling
« Reply #10 on: April 26, 2018, 08:45:37 PM »
The cooling unit uses heat to cool.  Yea, it makes no sense.  So yea it will be hot.  Again, like you have diacovered your issue is totally anmair flow issue.

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #11 on: April 26, 2018, 08:51:39 PM »
Ok, i have been running new fans for about 5 hrs and no change, still 54 😢 ill see in the morning, im currently running 2 3600rpm 1amp fans, i figured in 5 hrs it would of dropped some..

8Muddypaws

  • ---
  • Posts: 2546
Re: Rm1350 refer not cooling
« Reply #12 on: April 26, 2018, 09:03:48 PM »
It should be VERY hot!  Like barely able to put your hand on it for more than a second or two.

Well DUH on my part!

If you're running on AC power it may be that one of your two heating elements has gone bad.  It's a simple matter to test them with an ohmmeter.  Check your manual for the proper resistance.  They're not horribly expensive or hard to replace.

This also would explain why it cooled better while traveling.  It's running on propane then.

See page 16 of this manual : https://www.manualslib.com/manual/766001/Dometic-Rm1350.html#manual
« Last Edit: April 26, 2018, 09:08:13 PM by 8Muddypaws »
Retired computer professional
Musician, songwriter and music director
2006 Bounder 34H, 2008 CR-V Toad

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #13 on: April 27, 2018, 08:44:28 AM »
The boiler tank operates at about 350 F., so yes it should be extremely hot and the vertical tube above it also, though decreasing with distance.  The rest of the tubing on the return side should only be warm.

Muddypaws may have hit on the problem, i.e. a bad AC heater.  The RM1350 uses two 120v heaters in series, so in some failure modes you can lose heating capacity and cooling efficiency drops.  That would explain why it cools well on propane but not so well on 120v electric.  Try it on LP at the campsite and see how it performs.  If LP always works well, you can be confident that air flow, fans, etc. are all working as designed and that the problem is in the AC heater components. Note that low AC voltage to the fridge or a poor wire connection in the 120vac heater circuit would have the same effect.

http://bryantrv.com/docs2/docs/Service%20Manual,%20RM1350.pdf
« Last Edit: April 27, 2018, 08:53:01 AM by Gary RV_Wizard »
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #14 on: April 27, 2018, 04:49:34 PM »
Oms checked it and reading good, so now have it on l.p. for the night and see how it does.. crossing fingers

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #15 on: April 28, 2018, 11:03:12 AM »
Did you verify the voltage at the element as well as ohms? There isn't much electronics between the RV's 120v outlet and the heater elements, basically just a relay that turns power on/off, but its conceivable there is a low voltage problem.
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #16 on: April 29, 2018, 09:34:12 AM »
Still nothing, I oms checked heating elements, and it read 37.. which is good.. I'm going to more fans to exhaust today, instead of blow and see if that helps.. I want to thank everyone trying to help me troubleshoot this problem.. sounds like a air movement issue but it's just not bring it down any.. maybe ill just keep drive around to keep temp down..😂

8Muddypaws

  • ---
  • Posts: 2546
Re: Rm1350 refer not cooling
« Reply #17 on: April 29, 2018, 10:49:30 AM »
Have you checked the thermistor per the troubleshooting steps?  They have been known to go bad.
Retired computer professional
Musician, songwriter and music director
2006 Bounder 34H, 2008 CR-V Toad

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #18 on: April 29, 2018, 10:52:13 AM »
Yes, have even changed it.. 1st thing i did.. checked volts on elements.. 119.9 v👍 forcing air out now.. let's see how that goes.

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #19 on: April 29, 2018, 11:18:52 AM »
Rather than shotgun the problem with more fans, run it in LP gas mode for a day. If it cools ok in LP gas mode, then air flow is not the problem and you need to look elsewhere.  Ditto with the thermister - same one is used whether electric or LP. 
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #20 on: April 29, 2018, 11:20:04 AM »
Rather than shotgun the problem with more fans, run it in LP gas mode for a day. If it cools ok in LP gas mode, then air flow is not the problem and you need to look elsewhere.  Ditto with the thermister - same one is used whether electric or LP.

Gary he already ran it overnight on LP
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #21 on: April 30, 2018, 10:40:51 AM »
Well sucking air didnt help😢 call service tech, that was a waste of time and money, he had no clue himself. So went out and got a small refer.. had to have something to keep beer cold,😊 while troubleshooting this. Everything you have suggested, I've done..

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #22 on: April 30, 2018, 11:24:33 AM »
Quote
Gary he already ran it overnight on LP

I missed that (and still don't see it). Just that it ran on LP while traveling.  Since my reading of this topic seems to be deficient, what was the result of running on LP at the campsite?

If it runs fine on LP, both driving and parked, then it is pointless to fiddle with fans and air flow, cause those are identical whether using electric or gas. The only difference between electric and gas modes is the heat source for the boiler. Everything else works exactly the same.
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #23 on: April 30, 2018, 11:55:17 AM »
I missed that (and still don't see it). Just that it ran on LP while traveling.  Since my reading of this topic seems to be deficient, what was the result of running on LP at the campsite?

If it runs fine on LP, both driving and parked, then it is pointless to fiddle with fans and air flow, cause those are identical whether using electric or gas. The only difference between electric and gas modes is the heat source for the boiler. Everything else works exactly the same.

I got tangled up in the back and forth also, so went back and re-read each entry. On the 27th OP reported he would leave it running overnight on LP, and on the 29th he reported it still doesn't cool. I am confused by the earlier comments that it cooled OK while driving, which started a chase down the airflow path, but now it doesn't sound like that was anything more than an anomaly.

He's already changed thermistor, checked both heating elements, cleaned the chimney, installed a couple different versions of auxiliary fans, and tried it on both LP and electric and it still doesn't work. So if I've followed the story correctly he has a fridge which, on both LP and electric, marginally cools the freezer but won't get the fridge portion below 50, which in my much less learned than you opinion sounds like a classic cooling unit failure.
« Last Edit: April 30, 2018, 12:54:27 PM by Sun2Retire »
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

Rene T

  • Forum Staff
  • ---
  • *
  • Posts: 12090
  • Every day is payday and every payday I have off
Re: Rm1350 refer not cooling
« Reply #24 on: April 30, 2018, 12:21:38 PM »
I missed that (and still don't see it).

He mentioned it in Reply#14 and came back on Reply#16 and said it still didn't work.
« Last Edit: April 30, 2018, 03:42:59 PM by Rene T »
Rene, Lucille & co-pilot Buddy
AKA  Pep N Mem
2011 Chevy Duramax 2500 HD 4X4
2011 Montana High Country 343RL
From the Granite State of NH
& Florida Snowbird in Lakeland FL

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #25 on: April 30, 2018, 03:40:30 PM »
Sorry about all this confusion. I'm just trying to get this fix.. so ill repeat all that has happened and I have done.
I started camping ft, and the refer is maintaining 50°, so i changed the tremisor, and no change. After trying a couple things, I came to here and started asking questions.
Then I had to drive it to carpenter campers, for something else(they couldn't look at it)(about an hr total drive time) the temp dropped to 33° so then the thread started

. I have installed new fans to blow, ran on l.p. only, cleaned chimney, moved fans to exhaust instead of blow. I have oms checked heating elements, volt check everything and all the good, except the temp never goes below 48° that makes the freezer 26°

I hope this clears up the confusion, if the cooling unit is bad, then wouldn't not cool to 33° while driving??

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #26 on: April 30, 2018, 03:55:00 PM »
if the cooling unit is bad, then wouldn't not cool to 33° while driving??

I would have to agree, but the fact that no matter how much air is moved and all the other things you've tried it now won't cool either the freezer or the fridge properly (at mid range setting the freezer should at least be in low single digits and the fridge should be in the mid 30s, give or take).

What is the longest the unit has sat running without the doors being opened a single time?

Also, have you checked the seals on the doors? Open the door, then close the door on the bill. The door should grab the bill. Check the entire seal all around all doors.

What is the outside temp where you're located?
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #27 on: April 30, 2018, 04:03:21 PM »
The longest is has set without doors opening is approx 15hrs.
Doors checked like stated
In pensacola fla, temp is approx 73° day, 55 lows at times.
Also looking at getting a new cooling unit, and i see that they have insulation around the pipes.. mine dont have.. should they??

kdbgoat

  • ---
  • Posts: 5598
Re: Rm1350 refer not cooling
« Reply #28 on: April 30, 2018, 07:41:27 PM »
How are you checking the temperature in the fridge? If using a normal thermometer, the temperature will rise immensely as soon as you open the door. Use a pocket thermometer in about an inch of water in a glass, or a temperature sensor with a remote wireless readout.
I know you believe you understand what you think I said,
But I am not sure you realize what you heard is not what I meant


2016 Leprechaun 319DS

regval

  • ---
  • Posts: 275
Re: Rm1350 refer not cooling
« Reply #29 on: May 01, 2018, 12:07:09 AM »
I know that others have offered opinions on possible solutions so I'm not adding to those.
Below is a link to a YouTube video from a RV refrigerator professional that demonstrates how to determine if the cooling unit is functional by bypassing the electronic controls and using the 120VAC heating element of the refer only by rigging a direct connection to Ac voltage. Of course, it has the basic caveat that the refer must have adequate ventilation, be level, etc.

https://m.youtube.com/watch?v=k2bBSGuwU_o
2005 Forest River TT 27BHSS and 2009 Heartland Sundance 2998RB 5vr
2007 Chev Silverado 2500HD WT crew cab, LB, 6.6L, Allison 6sp, B&W Companion Hitch
Retired Biomedical Engineer


"Some come to the fountain of knowledge to drink, others just gargle."

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #30 on: May 01, 2018, 07:58:33 AM »
 Ok.. last thing I try and if cooling unit dont work, time to buy a new refer.. 😔 we have tried everything else.. and someone said cooling unit might be bad, looks like the best way to try it out for find out for sure..

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #31 on: May 01, 2018, 09:26:59 AM »
Quote
Also looking at getting a new cooling unit, and i see that they have insulation around the pipes.. mine dont have.. should they??

The function of the cooling unit requires that portions of it shed heat, so insulation would be counter-productive. Usually any insulation is at the boiler and the tube immediately above it and is a safety measure to protect the surroundings from the intense heat (about 350 F at that point).  Up near the top, there is a condensor that sheds heat to bring the coolant back to liquid and that must NOT be insulated on any way. Secondary heat shedding occurs at the two evaporators, which press firmly against the back wall of the fridge and conduct heat from the fins on the fridge interior.
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #32 on: May 01, 2018, 09:36:18 AM »
You do not need a new cooling unit if the fridge cools adequately under one circumstances and not others. It's the same cooling unit no matter what the circumstances.   But if it fails to cool in all modes and circumstances, then the cooling unit is the most likely culprit.

Based on your comments in Replies 13 & 14, it appears that LP mode does NOT cool, yet you reported 33 F while driving to the shop. If it were me, I would revisit the circumstances where [apparently] the fridge cooled OK and verify that whether that drive-time reading was a fluke or maybe a faulty measurement. Always measure the temperature as kdbgoat described, using a thermometer in water and allow time to stabilize. 
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

gravesdiesel

  • ---
  • Posts: 208
Re: Rm1350 refer not cooling
« Reply #33 on: May 01, 2018, 09:48:57 AM »
Could this be a 12v DC issue?  Maybe the voltage is low, coming from the converter/battery, versus when driving, when it could be 13.8-14v?  I know the 12v DC only runs the control board, relay and fans, but it seems everything else has been verified.
2016 KZ Spree 262 RKS
2003 Dodge 3500 4 door flatbed 4x4 diesel, 6 speed
1996 Dodge 3500 extra cab flatbed 4x4 diesel 5 speed
2006 Arctic Cat TRV diesel 4x4 ATV
(2) 1981 Yamaha G1 2 cycle golf carts
Many other diesels on the farm!

regval

  • ---
  • Posts: 275
Re: Rm1350 refer not cooling
« Reply #34 on: May 01, 2018, 10:32:39 AM »
Could this be a 12v DC issue?  Maybe the voltage is low, coming from the converter/battery, versus when driving, when it could be 13.8-14v?  I know the 12v DC only runs the control board, relay and fans, but it seems everything else has been verified.
Most RV refrigerators will work normally with the DC volts as low as 9.5V DC. The panel lights will even stay on with DC volts as low as 5V. However, there is a possibility that there may be AC volts riding on the DC volt source (referred to as AC ripple) and can cause erratic operation of the control board. Measuring the DC voltage with the DVM set to AC voltage should be done to determine if there is any AC voltage component while the camper is hooked up to shore power.  You would not get any AC ripple voltage from the trailer battery while driving.  So... just a thought for consideration.
2005 Forest River TT 27BHSS and 2009 Heartland Sundance 2998RB 5vr
2007 Chev Silverado 2500HD WT crew cab, LB, 6.6L, Allison 6sp, B&W Companion Hitch
Retired Biomedical Engineer


"Some come to the fountain of knowledge to drink, others just gargle."

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #35 on: May 01, 2018, 10:34:47 AM »
Based on your comments in Replies 13 & 14, it appears that LP mode does NOT cool, yet you reported 33 F while driving to the shop. If it were me, I would revisit the circumstances where [apparently] the fridge cooled OK and verify that whether that drive-time reading was a fluke or maybe a faulty measurement. Always measure the temperature as kdbgoat described, using a thermometer in water and allow time to stabilize.
Someone told me it might of shaken up the gas and gave me that number, so I'm going to try the direct wire and if this dont work, looks like a new refer, if it works then it sounds like a control board issue.. hoping for the best

Gary RV_Wizard

  • Forum Staff
  • ---
  • *
  • Posts: 64470
  • RVer Emeritus
Re: Rm1350 refer not cooling
« Reply #36 on: May 01, 2018, 06:56:01 PM »
Bypassing the thermostat doesn't prove anything, since you already know the heater element is receiving voltage (you measured voltage at the element, right?). Bypassing the control board with direct 120v is a way to diagnose the 120v relay on the board or a non-functional thermostat, but since the board is apply voltage to the heater, that is not at issue.

But have at it - it will give you piece of mind.
Gary
--------------
Gary Brinck
Summers: Black Mountain, NC
Home: Ocala National Forest, FL

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #37 on: May 01, 2018, 07:35:04 PM »
Yep, I did measure it, but the video said this is the best way to see if you have a bad cooling unit, or control board.. but your right peace of mind too..

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #38 on: May 01, 2018, 07:51:59 PM »
If you end up needing a new cooling unit I have yet to hear anything but praise for the “Amish” units. Pictures I’ve seen show increased coils and fins vs. OEM. I think the price is similar. And aside from wrestling the unit out on to the floor, supposedly not too complicated of a job.
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #39 on: May 02, 2018, 05:40:14 PM »
"If the freezer is cold but barely freezing and the inside of the refrigerator is cool, but not cool enough, you may still have a failing cooling unit due to internal restrictions in one or more of the cooling lines. This can happen if the refer was run off-level and got too hot, causing some of the internal chemicals to turn to solids."
Ok.. after running it for 24 hrs direct a.c., still no difference, then i added a "hurricane fan" to it and still no change😠😠😠 have to say cooling unit is a goner😤😠😠😠 so now debating, should I buy a new house refrigerator, new cooling unit , or just a new refrigerator?? I think that we have done everything possible to say the cooling unit is dead. So I'm leaning towards getting a new cooling unit, since I'm like 99.9999% sure evrything else is good.. what's you guys option?? I do want to thank everyone that has tried to help me in this.. grrr 1300.00 😠

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #40 on: May 11, 2018, 07:50:25 PM »
Update.. purchased a new cooling unit, installed today, fingers crossed.. it can't be anything else.. well see in morning

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #41 on: May 11, 2018, 08:25:51 PM »
it can't be anything else..
Better not be!  ;)
Which unit did you buy?
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #42 on: May 12, 2018, 04:45:18 AM »
Woo hoo its works😁😁😁 i bought the Amish one.. very helpful, great install instructions, I would recommend it to anyone.. communication before was great, shipment was fast.. only bad thing about them was they didn't install for me 😂

Sun2Retire

  • Photo moderator
  • ---
  • *
  • Posts: 3497
Re: Rm1350 refer not cooling
« Reply #43 on: May 12, 2018, 07:09:39 AM »
only bad thing about them was they didn't install for me


How long did it take?
Scott
Fulltiming in a 2005 Newmar Dutch Star 3810, Spartan, Cat C7 350
Eezrv TPMS, 970W Solar, Tri-Metric Battery monitor
2002 Dodge RAM 1500 Quad Cab toad
Stowmaster towbar & Brakemaster toad braking system

regval

  • ---
  • Posts: 275
Re: Rm1350 refer not cooling
« Reply #44 on: May 12, 2018, 09:19:01 PM »
Woo hoo its works😁😁😁 i bought the Amish one.. very helpful, great install instructions, I would recommend it to anyone.. communication before was great, shipment was fast.. only bad thing about them was they didn't install for me 😂

Great news. Experience is the best teacher I've found. You can put that knowledge in your pocket and maybe help someone else in the future.
2005 Forest River TT 27BHSS and 2009 Heartland Sundance 2998RB 5vr
2007 Chev Silverado 2500HD WT crew cab, LB, 6.6L, Allison 6sp, B&W Companion Hitch
Retired Biomedical Engineer


"Some come to the fountain of knowledge to drink, others just gargle."

Coopster8

  • ---
  • Posts: 41
Re: Rm1350 refer not cooling
« Reply #45 on: May 16, 2018, 02:53:45 PM »
Great news. Experience is the best teacher I've found. You can put that knowledge in your pocket and maybe help someone else in the future.
So true.. helping others is the key to happy future