Sponsored by Winnebago Industries

Author Topic: TV Cover  (Read 3703 times)

Weewun

  • Guest
TV Cover
« on: February 03, 2009, 03:52:40 PM »
Have a 2004 Winnebago Adventurer and wish to replace front tv with a digital LCD.  Trying to remove the plastic cover on the back of the enclosure with no success.  Have removed the 8 screws holding the cover to the ceiling and have looked for any thing else that may be holding it and have found no obvious holding devices.

Am afraid to pull too hard for fear of breakin the cover.  It seems to be held to the botton front frame board.  I can see no way to remove the TV without removing that cover. 

Any help will be appreciated.

judway

  • ---
  • Posts: 1017
  • We are at the house in West Melbourne, Florida
Re: TV Cover
« Reply #1 on: February 03, 2009, 04:32:48 PM »
Have you looked in the cabinets on each side of the TV?
Wayne
2003 Itasca Horizon 36LD
2017 Chevrolet Equinox LT
Remco Towbar, Demco Baseplate & Air Force One Brake
1995 GMC Sierra Z71
No Dogs      No Cats!
Retired Electrical Engineer (University of Cincinnati)
W4SRR

SargeW

  • Forum Staff
  • ---
  • *
  • Posts: 6301
  • Life is better on the road!
Re: TV Cover
« Reply #2 on: February 03, 2009, 05:30:15 PM »
On my 06' Meridian I have to remove the screws around the plastic you mentioned, and there is two round head metal screws through the cabinet on each side of the TV that screw into the wood frame around the TV.  I also have a sun visor under the TV cabinet that is held up with two screws on each side.  They also must be removed to as they screw into a metal brace on the bottom of the cabinet.

Sarge
Marty--
2017 Tiffin Allegro Bus 40SP
Cummins ISL 450 HP/Powerglide chassis
Visit our new travel blog! http://www.mytripjournal.com/rvnchickTNG
Support your local Police Officer, Fire Fighter and Military!

SargeW

  • Forum Staff
  • ---
  • *
  • Posts: 6301
  • Life is better on the road!
Re: TV Cover
« Reply #3 on: February 03, 2009, 05:43:12 PM »
Here are a few pic of my install about 6 months ago.

http://i459.photobucket.com/albums/qq314/SargeW/P3230051a-1.jpg

http://i459.photobucket.com/albums/qq314/SargeW/P3220047a.jpg
Attaching the brace board that the TV will hang on.

http://i459.photobucket.com/albums/qq314/SargeW/P3220031a.jpg
Doing the wiring.

Sarge
« Last Edit: February 03, 2009, 05:55:03 PM by SargeW »
Marty--
2017 Tiffin Allegro Bus 40SP
Cummins ISL 450 HP/Powerglide chassis
Visit our new travel blog! http://www.mytripjournal.com/rvnchickTNG
Support your local Police Officer, Fire Fighter and Military!

John Canfield

  • Forum Staff
  • ---
  • *
  • Posts: 11811
    • Jane and John's Internet Home
Re: TV Cover
« Reply #4 on: February 03, 2009, 07:38:45 PM »
You can also give Winnebago a call and ask them - check the resources sticky at the top of this forum.
--John
2005 Horizon 40AD, 2006 Jeep Rubicon Unlimited
Our Horizon projects
Our weather

Weewun

  • Guest
Re: TV Cover
« Reply #5 on: February 04, 2009, 06:39:00 PM »
Sargew and Judway, thks for your input.  Found the screws in the Cabinets beside the TV enclosure and the Wood Frame and Plastic Cover dropped out with no problem.  This my Brother-in Law's RV and we will build the supports for his new HDTV tomorrow.

I like the metal support housing that Winnebago uses, it will be a lot easier mounting the LCD than it was in my Monaco Diplomat.

Again thks.

 

Hosted by Over The Network