Recent content by marknoo

Thanks everyone. If I cannot solve it with all these ideas I deserve to explode. LOL

I have brand new propane hose, but it is going to go through a tight area and there may be some movement. I can't find a grommet to fill it in. I was thinking of maybe wrapping the part that of the hose that may get moved around with duct tape, so the duct tape will be harmed instead of the...

I believe I need a #33842 burner and it is no longer available. I found some posts that say another burner will work and others that say it won't. I ordered that burner head back in 2020 (I forgot the number, but the holes in it were much smaller than the holes in my OEM burner) and it did not...

Thanks for taking the time to answer my questions. It is appreciated. I sent a support ticket to Marey (they manufacture the EcoTemp L10). I also found an EZ Tankless that is probably a better fit for what I do with it It only costs $144 bucks and it is pretty much all plumbed in already...

Last weekend it was 116 degrees in Oregon. I turned on my hot water for a cool down shower and the system stopped working. Can a microswitch flip because it got too hot, between the temperature outside (116 degrees) and being inside a trailer compartment, and then the gas coming on to heat the...

Is there a gap filler used for noise, heat insulation that is also waterproof? I am thinking of gap filler like the "Great Stuff" brand type. I'm trying to keep the floor under my shower solid/intact until I can junk this trailer. and there has been a leak in the tube, it seems likely it has...

so I tried to find the igniter swtich but could not find it, OH, not by looking inside the furnace but on this diagram. I don't know what the combustion chamber is so I need to find it and then find that sensor. Does anyone see it on here...

So a new motor, a new circuit board, a new burner did not fix the problem. I just took my board into the RV place and they tested it and it is fine. They told me to check my igniter switch in the combustion chamber. They said if it is bad the motor will just keep running. which mine does, it...

My buddy is an IBEW electrician. So I asked him to look. The connector is OK he says. Then he had me show him the whole cycle. But this time I listened from outside the trailer, right next to the hatch that opens up to reveal the heater. The unit turns on, then you smell gas, next you hear a...

First off, I apologize for not getting back to you sooner. Second, thank you very much for answering. OR maybe thanks should be first. Anyway, thank you. When the heater is doing its start/stop thing the fan runs but there is no heat. Also, it doesn't stop "nicely". It stops very abruptly, it...

So I just replaced the circuit board in my heater, I also replaced the fan. It does have a loose connection to the circuit board but it always did. When I first replaced everything it would come on, go off, then come on and work like it should. Today it seems to want to come on, go off, come...

I do have one question. I bought the new battery and I checked the voltage at the convertor, the batter and at the heater. It measured about 12.7 volts. The guy at the trailer store said it should be 13.5, could that be what is interfering with my heater blower turning on. How long do you have...

The heater in my trailer went out a few months ago and I am now getting around to fixing it. I have replaced the batter, so it has proper power. That did not fix it. I had the RV store test my circuit board and it fires weird. It pulses super fast and then does not try to pulse again. (I...

Thanks to everyone for responding. I fixed the problem for now by replacing the 2nd pipe but I have lost confidence in the system. I am not sure how to proceed. I don't want to redo the whole trailer. Honestly, i don't think it is worth the effort. Anyway, you guys give great advice. So after I...

Last week it froze, but it got warmer and the water dethawed and everything seemed alright. Then a pipe burst. First I tried to fix it with some "emergency tape" than I tried some JB Water Weld (I even put some Gorilla glue on it) but none of it worked. So I then bought some tools to get crimped...