atwood

Hi All, This spring I want to change my anode rod. I have a 2005 Coachmen Concord 225RK. The current 4.5 inch rod is a black material. What is the best anode for my Atwood system? Thanks, Chris

I need your experienced help. My 2015 Jayco Pinnacle 36 RSQS 40K Atwood heater has worked perfectly. Suddenly, it stopped working. I was told to replace the sail switch. I purchased a two-pack from Amazon #36165, After I installed one of them, the heater worker for two nights and stopped. The...

04 Monaco Windsor, front heater has a bad heat exchanger, at least that's what I believe. When it runs have burned gasses filling the interior. It is an Atwood 8525-iv-dclp. Of coarse I tried searching before posting, but many of the links no longer work from the posts. What is the best...

My hot water tank stop working on the AC side. Gas side works fine. My question if the element is bad will the red light in the switch light?

So, what made me have the desire to spend money by removing the Atwood 6-gallon tank water heater and replace it with a Ranein on-demand water heater in our 2015 FWC Hawk Flatbed? A few years ago, I mounted a Quick Pitch shower enclosure on the side of the FWC, great now we can take more...

I read through previous posts on GC10A-4E replacement options throughout this forum and others. We travel fulltime and noted this morning that the HW tank is leaking - I was able to check all the pex connections and fittings going into the tank and saw no leaks; but there is a steady drip off...

My issue is that when my furnace in my 2015 ACE 30.1 fires it will run for about 10 seconds or so and go out and continue doing this, I have replaced the burner and electrode along with the sail switch and tried a new control board, If I run 12 volts from the reset switch to the air switch after...

Hi I have been fighting my Atwood furnace. It's a 8500. The furnace would inginte blow heat. Then the blower motor would keep running blowing cold air. It wouldn't shut off until I shut the thermostat off. Wait awhile then turn it back on. This would go on for days. So I replaced the sail switch...

Still trying to figure this thing out. So I replaced the high limit switch. It worked for a hour than stopped. So I dug back into the wires that went to the switch. And noticed one of the wires melted to the heat exchanger. So I fixed the wire. But now the blower motor doesn't want to kick on...

Everyone or anyone . . . The Atwood water heater in our 1972 Overlander stopped working. Ordinarily when I flip the remote switch, the red indicator light in the switch lights up and the ignition fires immediately. Now the light does not come on and the ignition does not fire. There is 13+...

I hope this is the right place to post this. My Atwood AFMD30111 starting smelling funnt and later started blowing soot out the combustion exhaust. No wasp nests or dirt dauber found anywhere. The burner tube looks okay to me and no bugs, spider webs, etc found in it. The orifice looked fine...

The furnace worked last night. Woke up around 1am blowing cold 🥶. Shut the thermostat off. Then waited for a while then turned it back on. The furnace did light but went out. I changed the sail switch but nothing happened. What is the next step? I have a electric board on order. Is there...

Atwood WH won't light, about to start troubleshooting but wondering has anyone changed a manual valve to an electronic one. It May be better if it can be done.

I could not get my hot water tank to run on Propane. I replaced the circuit board with the thermostats the fuse and it still won’t run on Propane for any length of time. I gave up and decided to run on electricity now the weirdest thing that’s happening is the hot water tank is hot, but I can’t...

the 110v heater element doesn't work , the limits switches are ok , question: in which hole the low temp LS goes ? left or right? also , are they same than the ones used in the furnace?

Hi All, Just picked up a 2008 Tiffin Phaeton 40QDH and first time trying to level the MH and...nothing...no lights on pad. I have spent some time troubleshooting, calling a tech hotline related to GoodSams, and have reached out to Tiffin tech support, but no luck yet. Here is where I am at...

I have a Atwood MPD 93756 hot water heater in my Thor ACE 29.4. LP side works good. 120vac is not. Doing some troubleshooting with 120vac on and I get 12v to both brown and white wires on control board. Next I get 12v on the second brown wire from the right side of t-stat but nothing on the...

Apparently there is a connection between the turn signals and our Atwood levelegs jacks. This is the second time I've had to replace the 15 amp turn signal fuse. Both times, when the fuse was blown, the Atwood levelegs jacks would not deploy. Replace the fuse and it works as it should. This...

Model GE16 ext shut off while running on gas. I bypassed the thermal cut off fuse just to see if it would fire up. No go. Lots of propane in the tank. Later I turned on the propane start switch inside the trailer and it fired up. Ran for about 10 min. And stopped again. This one has me baffled...

I have an Atwood GCH10A-4E hot water heater in our 2009 Journey 34y. Is there a short cut or work around to replace the electrical heating element other than pulling the entire unit? Thanks in advance for any guidance.

I have a 2018 Eagle, My furnace will light and the burner will start for about 3-5 seconds and then shut off. I have the Atwood Furnace. Has anyone else had this?

Jacks not engaging. The Atwood level legs system requires the Engine running light, the Park brake engaged light and the Park/neutral light all illuninate before the system will engage. We moved from one site to another this morning. The jacks worked fine as we prepared to leave. The site...

Jacks not engaging. The Atwood level legs system requires the Engine running light, the Park brake engaged light and the Park/neutral light all illuninate before the system will engage. We moved from one site to another this morning. The jacks worked fine as we prepared to leave. The site...

I have a 2022 Redhawk 26M with an Atwood furnace. When I set the touchscreen controller to "heat with gas" and a high set point temperature, i know tge furnace ignites because I can feel heat at tge external exhaust port and I hear a fan running in the unit. The air from the ceiling vents...

I have an Atwood model AFMD30141 furnace it will light off but stop within seconds. Any help would be greatly appreciated.