2015 Winnebago View Water Pump Not Running After De-Winterizing

[Randy Brown]

I'm following the directions to de-winterize my Winnebago View, but NO water comes out of the faucets. Apparently the water pumps (3) are not engaging.......what ideas do you have to get the pumps working so I can remove the anti-freeze and get fresh water working.
Help with ideas please...

 

[Arch Hoagland]

You have three water pumps? Never saw an RV that had three water pumps.

 

[Larry N.]

Apparently the water pumps (3) are not engaging.......

That might be three switches for one pump.

If you don't have water flow, then you may have some valves set in the wrong position.

 

[Randy Brown]

You have three water pumps? Never saw an RV that had three water pumps.

One lights up on the console above the refrigerator, there is a water pump switch in the bathroom, and another switch outside near the shower hose.

 

[Randy Brown]

my question isn;t about how many there are, but as to why they are not working, and pumping the water from the fresh water tank into the sinks...

 

[OldWEB]

One pump, co-located with the fresh water tank, find it and start tracing voltage with a voltmeter.
EDIT: Looking at the View manual, the pump may not be beside the tank, should be piped near it though.

 

[Randy Brown]

That might be three switches for one pump.

If you don't have water flow, then you may have some valves set in the wrong position.

can you clarify what you means by valve ? set in wrong position.......

 

[Randy Brown]

One pump, co-located with the fresh water tank, find it and start tracing voltage with a voltmeter.

can you clarify what you mean by tracing teh voltage...am I checking the voltage at each of the two water pump switches?

 

[OldWEB]

If you are de-winterizing, you know about the valves... is there water in the tank?
Is the pump running?
Voltage at the pump when there should be (switch "on")? Multiple switches usually means a pump relay.

Last chance Randy....

 

[Kirk]

If you have 3 switches for the water pump, then there is a pump controller that those connect to. Do you know if the one pump is actually running? It may be that the problem is not the pump. Here is a typical plumbing diagram.

o why they are not working, and pumping the water from the fresh water tank into the sinks...

Is there water in the freshwater tank?

can you clarify what you means by valve ?

I suspect that the reference is to the valve usually found between the water tank and the pump, which is there to allow the pump suction to be from a jug of antifreeze.

To determine if the pump is running and also to check that valve, you first must locate the water pump and the freshwater tank that supplies it.

 

[Larry N.]

can you clarify what you means by valve ? set in wrong position.......

See Kirk's post above, and note the valve references on the right side of the trailer diagram. Your View won't look exactly like the diagram, but the principle is the same.

 

[CharlesinGA]

What model View? We can then look at the plumbing drawings and probably figure this out.

 

[Kirk]

2015 Winnebago View plumbing drawings

 

[CharlesinGA]

I posted a couple of days ago, however the post disappeared or never made it.

If the OP will give us the year and exact model View, for example, 2010 View 24J, then we can look up the plumbing drawings for it on the WBO website.

 

[CharlesinGA]

Ok, i read the title, its a 2015. What model?

2015 Plumbing Diagrams​

• View (500)
  • 24G (Serial Number begins with 10542T1)
  • 24G (Serial Number begins with 10542T2)
  • 24J (Serial Number begins with 10538T1)
  • 24J (Serial Number begins with 10538T2)
  • 24M (Serial Number begins with 10544T1)
  • 24M (Serial Number begins with 10544T2)
  • 24V (Serial Number begins with 10545T1)
  • 24V (Serial Number begins with 10545T2)